All, we have the Norge/Sport 1200 2V Y-pipes now available again as well as the 8V colostomy bag replacements. Click on pics below to order. See verbal installation instructions below. We also have the Breva 1100 Y-pipe >HERE<
Getting rid of the “BAG” on a Breva/Norge/12S:
1. Put bike on side stand
2. Using a 10mm deep socket with short extension remove the chin fairing.
3. Loosen the clamps on the head pipes. Using 10mm socket
4. Remove muffler. Use 10mm socket on clamp and 13mm end wrench and 6mm allen on muff bolt Remove spring.
5. Unscrew the O2 sensor and let it hang
6. Remove the bolts on the exh flanges and remove the head pipes. 13mm deep socket w swivel
7. Put an oil pan under the rear of the engine
8. Pull the 2 hanger bolts and slip the “BAG” rearward as far as possible
9. Reach under the rear of the engine and unscrew the oil line from the oil pan and move to the side of the motor so it is clear of the BAG.
10. Now slide the BAG forward and down and it will slide out the right side providing you have a large drain pan.
11. Reattach the oil line.
12. Remove the seat and disconnect the positive cable on the battery.
13. Remove the cover on the starter using an allen wrench
14. Using a 13mm end wrench unbolt the starter and slide it back.
15. Cut the ty-wrap holding the O2 sensor. DO NOT CUT THE WIRE! Just let it hang.
16. Reinstall the starter and cover. And reconnect the battery.
17. Reinstall the seat.
Installing the new Crossover is a reverse of the above.
1. Place the new crossover in place. Hang it on the rear hanger .
2. Place the clamps with split rings over the ends of the crossover.
3. Install the head pipes loosly do not tighten.
4. Align pipes side to side and the crossover front to back and check clearance.
5. Install the muffler. Checking alignment before tightening. Install spring
6. Tighten clamps and head pipe flanges
7. Install O2 sensor.
8. Reinstall Chin fairing.
9. Check oil and fill as necessary.
10. Wipe header pipes down with alcohol to avoid spotting.
Getting rid of the “BAG” on a Breva/Norge/12S:
1. Put bike on side stand
2. Using a 10mm deep socket with short extension remove the chin fairing.
3. Loosen the clamps on the head pipes. Using 10mm socket
4. Remove muffler. Use 10mm socket on clamp and 13mm end wrench and 6mm allen on muff bolt Remove spring.
5. Unscrew the O2 sensor and let it hang
6. Remove the bolts on the exh flanges and remove the head pipes. 13mm deep socket w swivel
7. Put an oil pan under the rear of the engine
8. Pull the 2 hanger bolts and slip the “BAG” rearward as far as possible
9. Reach under the rear of the engine and unscrew the oil line from the oil pan and move to the side of the motor so it is clear of the BAG.
10. Now slide the BAG forward and down and it will slide out the right side providing you have a large drain pan.
11. Reattach the oil line.
12. Remove the seat and disconnect the positive cable on the battery.
13. Remove the cover on the starter using an allen wrench
14. Using a 13mm end wrench unbolt the starter and slide it back.
15. Cut the ty-wrap holding the O2 sensor. DO NOT CUT THE WIRE! Just let it hang.
16. Reinstall the starter and cover. And reconnect the battery.
17. Reinstall the seat.
Installing the new Crossover is a reverse of the above.
1. Place the new crossover in place. Hang it on the rear hanger .
2. Place the clamps with split rings over the ends of the crossover.
3. Install the head pipes loosly do not tighten.
4. Align pipes side to side and the crossover front to back and check clearance.
5. Install the muffler. Checking alignment before tightening. Install spring
6. Tighten clamps and head pipe flanges
7. Install O2 sensor.
8. Reinstall Chin fairing.
9. Check oil and fill as necessary.
10. Wipe header pipes down with alcohol to avoid spotting.